QC Equipment

Bursting Strength Double Head Paper & Board Test

  • Description
Bursting Strength is a widely used measure of resistance to rupture of various materials. A test specimen is held between two circular clamps and subjected to an increasing pressure from a rubber diaphragm. The rubber diaphragm is expanded by a controlled hydraulic pressure until the test specimen ruptures. The Bursting Strength of the specimen is the pressure reading at the time of rupture


Cobb Tester

  • Description
Cobb Test is the calculated mass of water absorbed in a specified time by 1 m of paper or board under specified conditions. The test area is 100 cm for Paper. The test is used for determining liquid absorptiveness or resilience of treated and untreated papers, boards, fabrics and other sheet materials. The test consists of a test apparatus, its 10-kg roller and blotting paper. The roller method is recommended to insure better consistency and reliability that can be obtained by manual blotting or rubbing the specimen


Compression Strength Tester

  • Description

Container Compression Tester is an efficient and easy to use equipment intended for measuring the ability of Corrugated or Solid fiber shipping containers to resist external compressive forces. This method describes how to determine the resistance of a fiberboard shipping container to compressive forces. This is accomplished by placing the container between two flat platens, one of which is mechanically driven to compress the box. A recording device is incorporated to indicate the force and deformation (deflection) required to compress the container.



Electronic Moisture Tester

  • Description

Electronic Moisture Tester is an electrical resistance type digital moisture meter. It calculates on the basis of mass of water / mass of solids. Since the clectrical conductivity of paper is considerably effected not only by its moisture content, but also by the paper temperature and various substances contained in the paper, it is necessary to take these influences into consideration in the design of the moisture meters to ensure accurate readings. The thin pins make it easy to measure the moisture content of paper, paperboard and corrugated board up to maximum thickness of 25mm.



Crush Testers & Sample Cutters

  • Description
Linux range of Crush Testers are designed for performing Ring Crush Test (RCT), Edge Crush Test (ECT), Flat Crush Test (FCT), Pin Adhesive Test (PAT), Concora Medium Test (CMT), Corrugated Crush Test (CCT) and other general compression tests, on a variety of materials like paper, paperboard, etc. These multi-functional equipments incorporate high accurate load cell and precise ball screw, which drives the compression platen steadily along the guide track to compress the specimen.


GSM Tester

  • Description
In paper manufacturing and user industry, the term for expressing the \"Weight\" per unit area, (more properly mass per unit area) of paper has been \"basis weight\", \"ream weight\", \"substance\", or \"grammage. Also in most countries, the mass per unit area is expressed in grams per square meter (gm.m). The area of several sheets of paper or paperboard is determined from linear measurement. The weight is determined by weighing. The grammage is calculated from the ratio of the mass to the area, after conversion to metric units when necessary.


ECT/FCT/PAT/RCT/CMT/CCT TESTER MACHINE

  • Description
Linux range of Crush Testers are designed for performing Ring Crush Test (RCT), Edge Crush Test (ECT), Flat Crush Test (FCT), Pin Adhesive Test (PAT), Concora Medium Test (CMT), Corrugated Crush Test (CCT) and other general compression tests, on a variety of materials like paper, paperboard, etc. These multi-functional equipment incorporate high accurate load cell and precise ball screw, which drives the compression platen steadily along the guide track to compress the specimen.


WEIGHT SCALEOF 1000 KG

  • Description

The 1000 kg floor weighing scale combines features of digital and mechanical systems to solve challenges of determining the weight of heavy items such as harvested products, feed ingredients prior to milling, finished feed, animals etc as well as grade products into required weights.



BARCORD SCANNER

  • Description

A bar-code reader consists of a a lens, light source and a light sensor which translates optical impulses into electrical ones. Moreover, nearly all barcode readers consists of a decoder circuitry that analyzes the barcode’s image data provided by the sensor and sends the barcode’s content to the scanner’s output port.



GUM TESTING MACHINE

  • Description
Box Gum Testing Machine is used to determine the Resistance of corrugated & non-corrugated boxes. The Instruments provides digital display of load and deformation, complete with memory for retaining peak value, automatic or normal zero setting and Overload & over travel protection facilities. This equipment is designed to measure ability of the container to resist external compression loads during transit and storage.


  • Description
Bursting Strength is a widely used measure of resistance to rupture of various materials. A test specimen is held between two circular clamps and subjected to an increasing pressure from a rubber diaphragm. The rubber diaphragm is expanded by a controlled hydraulic pressure until the test specimen ruptures. The Bursting Strength of the specimen is the pressure reading at the time of rupture
  • Description
Cobb Test is the calculated mass of water absorbed in a specified time by 1 m of paper or board under specified conditions. The test area is 100 cm for Paper. The test is used for determining liquid absorptiveness or resilience of treated and untreated papers, boards, fabrics and other sheet materials. The test consists of a test apparatus, its 10-kg roller and blotting paper. The roller method is recommended to insure better consistency and reliability that can be obtained by manual blotting or rubbing the specimen
  • Description

Container Compression Tester is an efficient and easy to use equipment intended for measuring the ability of Corrugated or Solid fiber shipping containers to resist external compressive forces. This method describes how to determine the resistance of a fiberboard shipping container to compressive forces. This is accomplished by placing the container between two flat platens, one of which is mechanically driven to compress the box. A recording device is incorporated to indicate the force and deformation (deflection) required to compress the container.

  • Description

Electronic Moisture Tester is an electrical resistance type digital moisture meter. It calculates on the basis of mass of water / mass of solids. Since the clectrical conductivity of paper is considerably effected not only by its moisture content, but also by the paper temperature and various substances contained in the paper, it is necessary to take these influences into consideration in the design of the moisture meters to ensure accurate readings. The thin pins make it easy to measure the moisture content of paper, paperboard and corrugated board up to maximum thickness of 25mm.

  • Description
Linux range of Crush Testers are designed for performing Ring Crush Test (RCT), Edge Crush Test (ECT), Flat Crush Test (FCT), Pin Adhesive Test (PAT), Concora Medium Test (CMT), Corrugated Crush Test (CCT) and other general compression tests, on a variety of materials like paper, paperboard, etc. These multi-functional equipments incorporate high accurate load cell and precise ball screw, which drives the compression platen steadily along the guide track to compress the specimen.
  • Description
In paper manufacturing and user industry, the term for expressing the \"Weight\" per unit area, (more properly mass per unit area) of paper has been \"basis weight\", \"ream weight\", \"substance\", or \"grammage. Also in most countries, the mass per unit area is expressed in grams per square meter (gm.m). The area of several sheets of paper or paperboard is determined from linear measurement. The weight is determined by weighing. The grammage is calculated from the ratio of the mass to the area, after conversion to metric units when necessary.
  • Description
Linux range of Crush Testers are designed for performing Ring Crush Test (RCT), Edge Crush Test (ECT), Flat Crush Test (FCT), Pin Adhesive Test (PAT), Concora Medium Test (CMT), Corrugated Crush Test (CCT) and other general compression tests, on a variety of materials like paper, paperboard, etc. These multi-functional equipment incorporate high accurate load cell and precise ball screw, which drives the compression platen steadily along the guide track to compress the specimen.
  • Description

The 1000 kg floor weighing scale combines features of digital and mechanical systems to solve challenges of determining the weight of heavy items such as harvested products, feed ingredients prior to milling, finished feed, animals etc as well as grade products into required weights.

  • Description

A bar-code reader consists of a a lens, light source and a light sensor which translates optical impulses into electrical ones. Moreover, nearly all barcode readers consists of a decoder circuitry that analyzes the barcode’s image data provided by the sensor and sends the barcode’s content to the scanner’s output port.

  • Description
Box Gum Testing Machine is used to determine the Resistance of corrugated & non-corrugated boxes. The Instruments provides digital display of load and deformation, complete with memory for retaining peak value, automatic or normal zero setting and Overload & over travel protection facilities. This equipment is designed to measure ability of the container to resist external compression loads during transit and storage.